Subaru Legacy BN/BS (2015-2019) Service Manual: Basic diagnostic procedure procedure

Subaru Legacy BN/BS (2015-2019) Service Manual / Immobilizer (diagnostics) / Basic diagnostic procedure procedure

1. WITHOUT KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM

CAUTION:

When the body integrated unit (except for C0 and C5 models) or the immobilizer CM (C0 and C5 models) is replaced, registration of the immobilizer system is required. For details, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

STEP	CHECK	YES	NO
1.CONFIRM NUMBER OF REGISTERED IMMOBILIZER KEY. Confirm the number of registered immobilizer key. For details, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.	Is the number of registration 0-	Register the immobilizer system.	Basic Diagnostic Procedure > PROCEDURE
2.CHECK SECURITY INDICATOR LIGHT. 1) Remove the ignition key from ignition switch. 2) Wait at least 60 seconds.	Does the security indicator light blink-	Basic Diagnostic Procedure > PROCEDURE	Check the security indicator light circuit. Diagnostics Chart for Security Indicator Light > INSPECTION
3.CHECK KEY SWITCH. Insert the ignition key in the ignition switch. (OFF or ACC)	Does the security indicator light remain blinking-	Check the key switch circuit. Diagnostics Chart for Security Indicator Light > INSPECTION	Basic Diagnostic Procedure > PROCEDURE
4.CHECK SECURITY INDICATOR LIGHT. Check the security indicator light status in the condition of step 3.	Does the security indicator light go off-	Basic Diagnostic Procedure > PROCEDURE	Basic Diagnostic Procedure > PROCEDURE
5.CHECK SECURITY INDICATOR LIGHT. Turn the ignition switch to ON.	Does the security indicator light go off-	Basic Diagnostic Procedure > PROCEDURE	Basic Diagnostic Procedure > PROCEDURE
6.CHECK ENGINE START. Turn the ignition switch to START.	Does the starter operate-	Check the LAN communication system. Basic Diagnostic Procedure	Basic Diagnostic Procedure > PROCEDURE
7.CHECK ENGINE START. Turn the ignition switch to START.	Does the engine start-	Immobilizer system is normal.	Basic Diagnostic Procedure > PROCEDURE
8.CHECK DTC. Read the DTC and time stamp of the system(s) below. Read Diagnostic Trouble Code (DTC) NOTE: For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION • Body integrated unit (except for C0 and C5 models) • Immobilizer CM (C0 and C5 models)	Is the DTC displayed on screen-	Basic Diagnostic Procedure > PROCEDURE	Replace the body integrated unit (except for C0 and C5 models) or the immobilizer CM (C0 and C5 models). Body Integrated Unit
9.CHECK DTC. Read the DTC and time stamp of the system(s) below. Read Diagnostic Trouble Code (DTC) NOTE: For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION • ECM	Is the DTC displayed on screen-	Basic Diagnostic Procedure > PROCEDURE	Perform the diagnosis for engine system. Basic Diagnostic Procedure > PROCEDURE Basic Diagnostic Procedure > PROCEDURE
10.CHECK FREEZE FRAME DATA. Check the freeze frame data.	Are the data recorded-	Record the data. Basic Diagnostic Procedure > PROCEDURE	Basic Diagnostic Procedure > PROCEDURE
11.CHECK DTC. Check the displayed DTC.	Are DTCs irrelevant to the immobilizer displayed-	Perform the diagnosis according to DTCs irrelevant to the immobilizer first.	Basic Diagnostic Procedure > PROCEDURE
12.PERFORM DIAGNOSIS. 1) Inspect using the “Diagnostic Procedure with Diagnostic Trouble Code (DTC)”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) 2) Repair the trouble cause. 3) Perform the Clear Memory Mode. Clear Memory Mode 4) Read DTCs again. Read Diagnostic Trouble Code (DTC)	Is the DTC displayed on screen-	Inspect using the “Diagnostic Procedure with Diagnostic Trouble Code (DTC)”. Diagnostic Procedure with Diagnostic Trouble Code (DTC)	Finish the diagnosis.

2. WITH KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM

NOTE:

For immobilizer diagnosis of model with the keyless access with push button start system, refer to “Keyless Access with Push Button Start System”. Basic Diagnostic Procedure

Immobilizer (diagnostics)

...

Clear memory mode operation

NOTE:For detailed operation procedures, refer to “Application help”.1. ECM1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle inform ...

Other materials:

Removal
1. SEDAN MODEL1. Disconnect the ground terminal from the battery sensor, and wait for at least 60 seconds before starting work. NOTE2. Remove the trim panel - rear pillar UPR. Rear Quarter Trim > REMOVAL3. Remove the noise suppressor assembly.(1) Remove the connector and harness clip.(2) Remove th ...