Honda Civic manuals

Subaru Legacy Service Manual: Dtc b1815 short in passenger's airbag dual stage - 2nd step

Subaru Legacy Service Manual / Airbag system (diagnostics) / Diagnostic chart with trouble code / Dtc b1815 short in passenger's airbag dual stage - 2nd step

DIAGNOSIS START CONDITION:

Ignition voltage is 10 V to 16 V.

DTC DETECTING CONDITION:

Shorted between +/− lines (shorted between main harness lines, shorted between passenger’s airbag lines, shorted between airbag CM internal lines)

CAUTION:

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION

NOTE:

Prior to starting work, prepare two AIRBAG RESISTORs (98299PA040).

WIRING DIAGRAM:

Airbag system Airbag System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the passenger’s airbag module.

Is there poor contact-

Replace the airbag main harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1815 SHORT IN PASSENGER'S AIRBAG DUAL STAGE - 2ND STEP

2.CHECK AIRBAG MAIN HARNESS (PASSENGER’S AIRBAG HARNESS) (SHORTED BETWEEN LINES).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connectors (AB7) and (AB2).

3) Disconnect the passenger’s airbag module connector (AB9).

4) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

5) Connect the connector (1AD) in test harness AD AV to the connectors (AB6, AB17, AB18).

6) Connect the connector (2AD) in test harness AD AV and the connector (1AG) in test harness AG.

7) Using a probe, measure the resistance between the terminals of connector (AB9). General Description > PREPARATION TOOL

CAUTION:

When measuring the resistance, make sure that the probe is inserted from the back side (harness side) of the connector. Also, do not insert the probe forcibly.

Connector & terminal

(AB9) No. 3 — (AB9) No. 4:

Is the resistance 1 M- or more-

Diagnostic Chart with Trouble Code > DTC B1815 SHORT IN PASSENGER'S AIRBAG DUAL STAGE - 2ND STEP

Replace the airbag main harness along with body harness.

3.CHECK AIRBAG CONTROL MODULE.

1) Disconnect the test harness AD AV from the connectors (AB6, AB17, AB18).

2) Connect the connector other than passenger’s airbag module connector (AB9).

3) Connect the battery ground terminal and turn the ignition switch to ON.

4) Clear the memory. Clear Memory Mode

5) Perform the Inspection Mode. Inspection Mode

6) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)

Is DTC B1815 displayed-

Replace the airbag control module. Airbag Control Module > REMOVAL

Diagnostic Chart with Trouble Code > DTC B1815 SHORT IN PASSENGER'S AIRBAG DUAL STAGE - 2ND STEP

4.CHECK PASSENGER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Connect the passenger’s airbag module connector (AB9).

3) Connect the battery ground terminal and turn the ignition switch to ON.

4) Clear the memory. Clear Memory Mode

5) Perform the Inspection Mode. Inspection Mode

6) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)

Is DTC B1815 displayed-

Replace the passenger’s airbag module. Passenger’s Airbag Module > REMOVAL

Diagnostic Chart with Trouble Code > DTC B1815 SHORT IN PASSENGER'S AIRBAG DUAL STAGE - 2ND STEP

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)

Is any other DTC displayed-

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)

Finish the diagnosis.

Dtc b1816 open in passenger's airbag dual stage - 2nd step
DIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Open circuit failure (open circuit in main harness, open circuit in passenger’s airbag, open circuit in airbag ...

Dtc b1813 short in driver's airbag dual stage - 2nd step circuit (to +b)
DIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Short circuit failure in power supply (shorted in main harness power supply, shorted in roll connector power supply, ...

Other materials:

Disassembly
Using the ST or a hydraulic press, push out the bolt - hub (b) from the hub unit COMPL - front axle (a).CAUTION:• Be careful not to hammer the bolts - hub. This may deform the hub unit COMPL.• Do not reuse the bolt - hub.NOTE:Since the hub unit COMPL can not be disassembled, only bolts - ...

© 2017-2019 Copyright www.sulegacy.com