Honda Civic manuals

Subaru Legacy Service Manual: Dtc p0016 crankshaft position - camshaft position correlation bank 1 sensor a

Subaru Legacy Service Manual / Engine (diagnostics)(h6do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0016 crankshaft position - camshaft position correlation bank 1 sensor a

DTC DETECTING CONDITION:

Detected when two consecutive driving cycles with fault occur.

TROUBLE SYMPTOM:

Engine stalls.

Improper idling

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.

STEPCHECKYESNO

1.CHECK CURRENT DATA.

1) Start the engine and let it idle.

2) Read the values of «VVT Adv. Ang. Amount R» and «OCV Duty R» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Read Current Data For Engine”. Subaru Select Monitor

Is the value of «VVT Adv. Ang. Amount R» approx. 0 deg, and the value of «OCV Duty R» approx. 10%-

Perform the following procedures, and clean the oil routing.

Replace the engine oil and idle the engine for 5 minutes, and then replace the oil filter and engine oil. Engine Oil > REPLACEMENT Engine Oil Filter

Check the following item and repair or replace if necessary.

Oil pipe (clog)

Oil flow control solenoid valve (clog or dirt of oil routing, setting of spring)

Intake camshaft (dirt, damage of camshaft)

Timing chain (matching of timing mark)

1. OUTLINE OF DIAGNOSIS

Detect the AVCS system malfunction.

Judge as NG when standard timing advance amount is far from learning angle.

2. COMPONENT DESCRIPTION

(1)

AVCS timing controller

(3)

Engine control module (ECM)

(5)

Hydraulic

(2)

Vane

(4)

Oil flow control solenoid valve

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

Battery voltage

≥ 10.9 V

Elapsed time after the neutral position switch changed

≥ 3000 ms

AVCS learning

In operation

4. GENERAL DRIVING CYCLE

Perform the diagnosis continuously after starting engine and while AVCS is not operating.

5. DIAGNOSTIC METHOD

Judge as NG when the absolute value of the difference between cam signal input position and learning value is out of specification.

Diagnosis 1

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

|Crankshaft position when camshaft position sensor signal is input − Learning value|

> 12 °CA

Time Needed for Diagnosis: 5000 ms

Diagnosis 2

Judgment Value

Malfunction Criteria

Threshold Value

Camshaft position sensor signal input position

< 18.80 °CA

or

> 56.80 °CA

Time Needed for Diagnosis: 5000 ms

Malfunction Indicator Light Illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

NOTE:

Initial standard learning value is the value of crank angle initially input at the production plant. And then it will be updated every time normal judgment has been completed. Learning value will not be updated if NG judgment occurs because timing belt or chain derails suddenly in process or because wrong assembly occurs during servicing.

Dtc p0017 crankshaft position - camshaft position correlation bank 1 sensor b
DTC DETECTING CONDITION:Detected when two consecutive driving cycles with fault occur.TROUBLE SYMPTOM:• Engine stalls.• Improper idlingCAUTION:After servicing or replacing faulty parts, pe ...

Dtc p0014 "b" camshaft position - timing over-advanced or system performance bank 1
DTC DETECTING CONDITION:Detected when two consecutive driving cycles with fault occur.TROUBLE SYMPTOM:• Engine stalls.• Improper idlingCAUTION:After servicing or replacing faulty parts, pe ...

Other materials:

Removal
1. Shift the select lever to “N” range.2. Disconnect the ground terminal from battery sensor. NOTE3. Lift up the vehicle.4. Remove the center exhaust pipe. (2.5 L model) Center Exhaust Pipe > REMOVAL5. Remove the front exhaust pipe and rear exhaust pipe. (3.6 L model) Front Exhaust Pi ...

© 2017-2019 Copyright www.sulegacy.com