Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc u0122 lost communication with vehicle dynamics control module

DTC DETECTING CONDITION:

No data from VDCCM is received.

TROUBLE SYMPTOM:

ABS warning light and VDC warning light illuminate.

STEPCHECKYESNO

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 8-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

Perform the basic diagnostic procedure. Basic Diagnostic Procedure

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed-

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

3.CHECK DTC.

Check the displayed DTC.

Is U0122 a current malfunction-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check

2) Read the DTC using Subaru Select Monitor.

Is U0122 a current malfunction-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems.

Is the VDC data no-receive detected in several modules-

Replace the VDC CM. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

6.REPLACE MODULE.

1) Replace the VDC CM.

2) Read the DTC using Subaru Select Monitor.

Is U0122 a current malfunction-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

System is normal.

7.CHECK MODULE.

1) Reinstall the VDC CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor.

Is U0122 a current malfunction-

Replace the VDC CM. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor.

Is U0122 a current malfunction-

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULE

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector-

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0126 lost communication with steering angle sensor module
DTC DETECTING CONDITION:No data is received from steering angle sensor.TROUBLE SYMPTOM:VDC CM does not operate normally.STEPCHECKYESNO1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.Was the basic dia ...

Dtc u1232 lost communication with rear/side radar control module
DTC DETECTING CONDITION:No data is received from radar sensor.TROUBLE SYMPTOM:Radar sensor does not operate normally.STEPCHECKYESNO1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.Was the basic diagno ...

Other materials:

Dtc p0451 evap system (cpc) pressure sensor/switch circuit range/performance
DTC DETECTING CONDITION:Detected when two consecutive driving cycles with fault occur.CAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.STEPCHECKYESNO1.CHECK FOR ANY OTHER DTC ON DISPLAY.Is an ...

© 2017-2024 Copyright www.sulegacy.com