Honda Civic manuals

Subaru Legacy Service Manual: List of cancel code list

NOTE:

The cancel code is registered even when cancel is performed intentionally by the driver.

Cancel codes are cleared if the ignition switch is turned to OFF.

If a different cancel code is input after a cancel code (latest code) has been input, the latest code is overwritten.

If the cruise indicator light is flashing, a malfunction is occurring in the system or cruise control related switch. The cancel code at this time is saved even after ignition switch is OFF as a memory code of a past malfunction.

To display a cancel code, use the Subaru Select Monitor to read the code after the cruise control is deactivated during a driving test.

Cancel code

Item

Contents of diagnosis

Note

11

Main Switch

CRUISE switch of cruise control command switch is turned to OFF, and then the cruise control is released.

This code is displayed without operating the CRUISE switch. Diagnostic Procedure with Cancel Code > 11

12

Stop & Brake switch

Stop light switch or brake switch is turned to ON, and then the cruise control is released.

This code is displayed without depressing the brake pedal. Diagnostic Procedure with Cancel Code > 12

13

Clutch Switch

Clutch switch is turned to ON, and then the cruise control is released.

This code is displayed without depressing the clutch pedal. Diagnostic Procedure with Cancel Code > 13

14

Neutral

Neutral position switch is turned to ON, and then the cruise control is released.

This code is displayed without shifting to neutral position. Diagnostic Procedure with Cancel Code > 14

15

Cancel switch

Cancel switch is turned to ON, and then the cruise control is released.

This code is displayed without operating the cancel switch. Diagnostic Procedure with Cancel Code > 15

16

Ignition switch

Ignition switch is turned to OFF, and then the cruise control is released.

This code is displayed without operating the ignition switch. Diagnostic Procedure with Cancel Code > 16

21

Abnormality of switches when Ignition switch on

When the ignition switch is turned to ON, each switch of cruise control command switch is already turned to ON.

This code is displayed when the ignition switch is turned to ON without operating the cruise control command switch. Diagnostic Procedure with Cancel Code > 21

22

Abnormality of change in vehicle speed

Malfunction of vehicle speed signal variation is detected.

Diagnostic Procedure with Cancel Code > 22

24

Abnormality of switches related to cruise control

Open circuit of the cruise control switch is detected during cruise driving. (The system is judged as model without cruise control.)

This code is displayed with normal operation. Diagnostic Procedure with Cancel Code > 24

31

Abnormal engine speed Signal

Abnormal increase of engine speed is detected.

Gear is placed in Neutral, 1st (MT model only) or Reverse position.

Cruise in 2nd shift position or more. Diagnostic Procedure with Cancel Code > 31

32

Cruse Control out of Range

Controlled vehicle speed decreased under the limit during cruising.

Set operation was performed at vehicle speed unavailable for setting.

RESUME operation was performed without memorized vehicle speed.

This code is displayed, though the vehicle speed is increased to the speed available for cruise set and set operation was performed again. Diagnostic Procedure with Cancel Code > 32

34

Prohibition of cruise control at continuing big Accel. angle

The vehicle has been driven at higher speed than set vehicle speed for an abnormally long time (approximately 10 minutes) during cruise driving.

This code is displayed when driving for a long period of time at higher speed than appropriate cruise set vehicle speed by operating accelerator pedal. In this case, the cruise setting is deactivated. Diagnostic Procedure with Cancel Code > 34

35

Prohibition of cruise control at vehicle speed F/B malfunction

Set vehicle speed cannot be kept because of some reasons (steep uphill, parking brake, abnormal decrease of engine output, etc.) during cruise driving.

This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause. Diagnostic Procedure with Cancel Code > 35

41

VDC/TCS Operating

Vehicle dynamics control (VDC), TCS or EPB is operated during cruise driving or cruise setting.

This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause. Diagnostic Procedure with Cancel Code > 41

43

ABS/VDC Failure

ABS or Vehicle dynamics control (VDC) system malfunction is detected during cruise driving or cruise setting.

Diagnostic Procedure with Cancel Code > 43

44

Body Integrated unit Failure

Body integrated unit system malfunction is detected during cruise driving or cruise setting.

Diagnostic Procedure with Cancel Code > 44

45

Meter Failure

Combination meter malfunction is detected during cruise driving or cruise setting.

Diagnostic Procedure with Cancel Code > 45

49

TCM Failure

Transmission control module (TCM) malfunction is detected during cruise driving or cruise setting.

Diagnostic Procedure with Cancel Code > 49

61

Brake switch abnormal

Malfunction in the stop light & brake switch is detected.

Diagnostic Procedure with Cancel Code > 61

62

Neutral Switch Failure

Neutral position switch malfunction is detected.

Diagnostic Procedure with Cancel Code > 62

63

Abnormality 1 of change in vehicle speed

Malfunction of vehicle speed signal variation is detected.

Diagnostic Procedure with Cancel Code > 63

64

Engine Sensor Failure 1

Malfunction related to engine is detected.

Diagnostic Procedure with Cancel Code > 64

65

Abnormality 1 of switches related to cruise control

Cruise control command switch malfunction is detected. (When the switch is pressed ON for a long time (approximately two minutes), stuck ON condition is detected.)

Diagnostic Procedure with Cancel Code > 65

66

Cruise Control Calculation Error

Malfunction of the cruise control calculation (microcomputer) is detected.

Diagnostic Procedure with Cancel Code > 66

Electrical component location location
(1)Inhibitor switch (CVT model)(5)Neutral position switch (MT model)(8)Data link connector(2)TCM (engine type: EZ)(6)Cruise indicator light and cruise set indicator light(9)Clutch switch (MT model)(3) ...

Read cancel code operation
1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. ...

Other materials:

Dtc p0122 throttle/pedal position sensor/switch "a" circuit low
DTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:• Improper idling• Engine stalls.• Poor driving performanceCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PRO ...

© 2017-2019 Copyright www.sulegacy.com