Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc p014c a/f / o2 sensor slow response - rich to lean bank 1 sensor 1

Subaru Legacy BN/BS (2015-2019) Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p014c a/f / o2 sensor slow response - rich to lean bank 1 sensor 1

DTC DETECTING CONDITION:

Detected when two consecutive driving cycles with fault occur.

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.

STEP	CHECK	YES	NO
1.CHECK EXHAUST SYSTEM. NOTE: Check the following items. • Loose installation of front portion of exhaust pipe onto cylinder heads • Loose connection between front exhaust pipe and front catalytic converter • Damage of exhaust pipe resulting in a hole	Is there any fault in exhaust system-	Repair the exhaust system.	Replace the front oxygen (A/F) sensor. Front Oxygen (A/F) Sensor

1. OUTLINE OF DIAGNOSIS

Detect the slow response of front oxygen (A/F) sensor.

For diagnosis, detect the trouble by processing the λ waveform in normal driving without forcibly changing the target air fuel ratio.

2. COMPONENT DESCRIPTION

(A)	Electromotive force	(B)	Air fuel ratio	(C)	Rich
(D)	Lean

(1)	Exhaust gas	(2)	ZrO2

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	> 10.9 V
Closed loop control with main feedback (3000 ms or more)	Operation
Engine speed	≥ 1000 rpm
Intake air amount	≥ 10 g/s (0.35 oz/s)

4. GENERAL DRIVING CYCLE

Perform diagnosis only once in a city driving including normal acceleration and deceleration.

5. DIAGNOSTIC METHOD 1

Detect the malfunction by checking “Cumulative value of time when λ changes from lean > rich” in comparison to “Time during which diagnosis is in progress”.

(A)

Time during which diagnosis is in progress

(B)

Cumulative value of time when λ changes from lean > rich

Judge as NG when the following conditions are established.

Judgment Value

Malfunction Criteria	Threshold Value	DTC
(Cumulative value of time when λ changes from lean > rich) / (Time during which diagnosis is in progress)	< 0.35	P014C
	> 0.65	P014D

Time Needed for Diagnosis: 70000 ms

Malfunction Indicator Light Illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

6. DIAGNOSTIC METHOD 2

Detect the malfunction by the cumulative value obtained from the amount of variation in λ change.

Judge as NG when the following conditions are established.

Judgment Value

Malfunction Criteria

Threshold Value

DTC

Cumulative value obtained from the amount of variation in λ change

Σ |(lambda(n) − lambda(n-1)) − (lambda(n-1) − lambda(n-2))|

< Value from Map

P014C and P014D

Map

Cumulative value obtained from the amount of variation in λ

Σ |lambda(n) − lambda(n-1)|

0.00

3.50

Cumulative value obtained from the amount of variation in λ change

0.00

3.50

Time Needed for Diagnosis: 70000 ms

Malfunction Indicator Light Illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

Dtc p014d a/f / o2 sensor slow response - lean to rich bank 1 sensor 1

NOTE:For the diagnostic procedure, refer to DTC P014C. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P014C A/F / O2 SENSOR SLOW RESPONSE - RICH TO LEAN BANK 1 SENSOR 11. OUTLINE OF DI ...

Dtc p0141 o2 sensor heater circuit bank 1 sensor 2

Refer to DTC P0037 for diagnostic procedure. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0037 A/F / O2 HEATER CONTROL CIRCUIT LOW BANK 1 SENSOR 21. OUTLINE OF DIAGNOSISDetect malfu ...

Other materials:

Removal
CAUTION:Refer to “CAUTION” of “General Description” before handling the airbag system components. General Description > CAUTION1. Turn the ignition switch to OFF.2. Disconnect the ground terminal from the battery sensor, and wait for at least 60 seconds before starting work. ...