Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b1015 key interlock circuit

DTC DETECTING CONDITION:

Short to ground in key interlock circuit

Key interlock output monitor is OFF, while BAT power supply voltage is 8.3 V or more and key lock operation judgment condition is met.

Time Needed for Diagnosis:

50 ms or more

TROUBLE SYMPTOM:

Key interlock does not keep lock condition.

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Shift lock control system Shift Lock Control System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK DTC.

1) Insert the ignition key.

2) Turn the ignition switch to ON.

3) Shift to the Neutral range.

4) Shift into P range.

5) Shift to the Neutral range.

6) Shift into P range.

7) Shift to the Neutral range.

8) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)

Is DTC B1015 displayed- (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK KEY LOCK SOLENOID.

1) Turn the ignition switch to OFF.

2) Disconnect the key lock solenoid connector (i52).

3) Measure the resistance between the key lock solenoid connector.

Connector & terminal

(i52) No. 1 — No. 2:

Is the resistance 103 — 115 --

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT

Replace the key lock solenoid. Key Lock Cylinders

3.CHECK HARNESS (GROUND SHORT CIRCUIT).

1) Disconnect the body integrated unit connector.

2) Measure the resistance between body integrated unit and chassis ground using tester.

Connector & terminal

(B280) No. 5 — Chassis ground:

Is the resistance 1 M- or more-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT

Repair or replace the short circuit of the harness.

4.CHECK CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector.

Is there poor contact at disconnected connector terminal-

Repair the terminal where poor contact exists, or replace harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT

5.CHECK DTC.

1) Insert the ignition key.

2) Turn the ignition switch to ON.

3) Shift to the Neutral range.

4) Shift into P range.

5) Shift to the Neutral range.

6) Shift into P range.

7) Shift to the Neutral range.

8) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)

Is DTC B1015 displayed- (Current malfunction)

Replace the body integrated unit. Body Integrated Unit

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b1016 shift lock circuit
DTC DETECTING CONDITION:• Shift lock circuit is open, or shorted to power or ground.• Shift lock solenoid output monitor is OFF, while BAT power supply voltage is 8.3 V or more and shift l ...

Dtc b1014 acc power
DTC DETECTING CONDITION:Voltage failure caused by poor contact of ACC power supply circuitACC voltage was outside the range of 8.3 — 16.7 V, when ACC power supply was ON.Time Needed for Diagnosis:40 ...

Other materials:

Installation
CAUTION:• Make sure the electrical connector is connected securely.• Make sure that each meter operates normally.• When the combination meter assembly of the model without keyless access with push button start has been replaced, perform the registration of immobilizer. (Except for ...

© 2017-2024 Copyright www.sulegacy.com