Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b1835 short in curtain airbag lh squib circuit

DIAGNOSIS START CONDITION:

Ignition voltage is 10 V to 16 V.

DTC DETECTING CONDITION:

Shorted between +/− lines (shorted between main harness lines, shorted between curtain airbag LH lines, shorted between airbag CM internal lines)

CAUTION:

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Airbag system Airbag System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, curtain airbag module LH and the curtain airbag sensor LH.

Is there poor contact-

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1835 SHORT IN CURTAIN AIRBAG LH SQUIB CIRCUIT

2.CHECK CURTAIN AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB31) from curtain airbag module LH.

3) Connect the connector (1N) in the test harness N to the connector (AB31).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for 6 seconds and go off-

Replace the curtain airbag module LH. Curtain Airbag Module

Diagnostic Chart with Trouble Code > DTC B1835 SHORT IN CURTAIN AIRBAG LH SQUIB CIRCUIT

3.CHECK AIRBAG REAR HARNESS (CURTAIN AIRBAG MODULE HARNESS LH) (SHORTED BETWEEN LINES).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB21) from seat belt pretensioner LH.

3) Disconnect the connector (AB5) from seat cushion airbag module LH.

4) Disconnect the connector (AB19) from side airbag module LH.

5) Disconnect the airbag resistor from test harness N.

6) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

7) Connect the connector (1AD) in test harness AD AV to the connectors (AB6, AB17, AB18).

8) Connect the connector (2AD) in test harness AD AV and the connector (1AG) in test harness AG.

9) Measure the resistance between connector (2N) terminals in test harness N.

Connector & terminal

(2N) No. 1 — (2N) No. 2:

Is the resistance 1 M- or more-

Diagnostic Chart with Trouble Code > DTC B1835 SHORT IN CURTAIN AIRBAG LH SQUIB CIRCUIT

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode

3) Perform the Inspection Mode. Inspection Mode

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)

Is DTC B1835 displayed-

Replace the airbag control module. Airbag Control Module

Diagnostic Chart with Trouble Code > DTC B1835 SHORT IN CURTAIN AIRBAG LH SQUIB CIRCUIT

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)

Is any other DTC displayed-

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)

Finish the diagnosis.

Dtc b1836 open in curtain airbag lh squib circuit
DIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Open circuit failure (open circuit in main harness, open circuit in curtain airbag LH, open circuit in airbag CM inte ...

Dtc b1833 short in curtain shield airbag rh squib circuit (to +b)
DIAGNOSIS START CONDITION:Ignition voltage is 10 V to 16 V.DTC DETECTING CONDITION:Short circuit failure in power supply (shorted in main harness power supply, shorted in curtain airbag RH power suppl ...

Other materials:

Removal
1. WATER PIPE ASSEMBLY RH1. Disconnect the ground terminal from battery sensor. NOTE2. Drain engine coolant. Engine Coolant > REPLACEMENT3. Remove the front exhaust pipe. Front Exhaust Pipe > REMOVAL4. Disconnect the engine coolant hose (A) from the water pipe assembly RH, and remove the bolt (B) ...

© 2017-2024 Copyright www.sulegacy.com