Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b2274 acc relay control circuit

Subaru Legacy BN/BS (2015-2019) Service Manual / Keyless access with push button start system (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc b2274 acc relay control circuit

DTC DETECTING CONDITION:

When malfunction is detected in ACC relay drive circuit in the keyless access CM or external circuit.

TROUBLE SYMPTOM:

Each function does not operate at the ACC position.

CAUTION:

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Stop light system Stop Light System > WIRING DIAGRAM

STEP	CHECK	YES	NO
1.CHECK LAN SYSTEM. Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE	Is LAN system normal-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Perform the inspection according to the diagnosis for LAN system.
2.CHECK FUSE. Remove the fuse. Relay and Fuse > INSPECTION	Is the fuse OK-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Replace the fuse. When the replaced fuse is blown immediately, check the power supply circuit for short-circuited.
3.CHECK HARNESS. 1) Disconnect the keyless access CM connector. 2) Using a tester, measure the resistance between the keyless access CM connector and chassis ground. Connector & terminal (i75) No. 24 (+) — Chassis ground (−): (i241) No. 40 (+) — Chassis ground (−):	Is the voltage 9.5 — 16 V-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Check the power supply circuit.
4.CHECK HARNESS. Using a tester, measure the resistance between the keyless access CM connector and chassis ground. Connector & terminal (i241) No. 21 — Chassis ground: (i75) No. 1 — Chassis ground:	Is the resistance less than 1 --	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Repair or replace the open circuit of harness.
5.CHECK HARNESS. 1) Disconnect the keyless access CM connector. 2) Using a tester, measure the resistance between the keyless access CM connector and chassis ground. Connector & terminal (i75) No. 23 — Chassis ground:	Is resistance 152.61 — 216.5 -- (20°C)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT
6.CHECK RELAY. Perform inspection of ACC relay unit. Relay and Fuse	Is the relay OK-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Replace the relay.
7.CHECK HARNESS. Using a tester, measure the resistance between keyless access CM connectors. Connector & terminal (i75) No. 23 — (i137) No. 2: (i136) No. 6 — Chassis ground:	Is the resistance less than 1 --	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2274 ACC RELAY CONTROL CIRCUIT	Repair or replace the open circuit of harness.
8.CHECK KEYLESS ACCESS CM. 1) Connect the keyless access CM connector. 2) Using a tester, measure the voltage between keyless access CM connectors. Connector & terminal (i75) No. 23 (+) — Chassis ground (−):	Is the voltage 1 V or less > 9.5 — 16 V when OFF > ACC ON-	Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again. NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.	Replace the keyless access CM. Keyless Access CM

Dtc b2275 engine start request control circuit

DTC DETECTING CONDITION:• When malfunction is detected in engine start permission signal output circuit in the keyless access CM.• When malfunction is detected in external engine start per ...

Dtc b2271 ign relay control circuit

DTC DETECTING CONDITION:• When malfunction is detected in IG1 and IG2 drive circuits in the keyless access CM.• When malfunction is detected in IG hold circuit in the keyless access CM.TRO ...

Other materials:

Dtc b14b3 seat heater thermistor circuit open (passenger)
DTC DETECTING CONDITION:Open circuit in seat heater thermistor.TROUBLE SYMPTOM:Seat heater RH does not function.WIRING DIAGRAM:NOTE:For the coupling connector, refer to “WIRING SYSTEM”.Seat Heater System Seat Heater System > WIRING DIAGRAMSTEPCHECKYESNO1.CHECK CONNECTOR.1) Check connect ...