Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b2a08 sos button circuit

DIAGNOSIS START CONDITION:

When ignition switch is ON.

DTC DETECTING CONDITION:

The following conditions occur for at least 50 ms.

SOS button impedance is more than 10 k-.

SOS button is stuck for at least 60 seconds.

TROUBLE SYMPTOM:

SOS function cannot be used.

RED LED illuminates.

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Telematics Telematics System > WIRING DIAGRAM

CAUTION:

CommCheck is required after replacing the DCM. Telematics System > OPERATION

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC. Diagnostic Code(s) Display

Is DTC B2A08 displayed- (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A08 SOS BUTTON CIRCUIT

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK HARNESS (OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the telematics button connector.

3) Disconnect the DCM connector.

4) Measure the resistance between telematics button connector and DCM connector.

Connector & terminal

(i270) No. 5 — (AD2) No. 6:
(AD2) No. 1 — Chassis ground:

Is the resistance 1 - or less-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A08 SOS BUTTON CIRCUIT

Repair or replace the open circuit of harness.

3.CHECK HARNESS (GROUND SHORT CIRCUIT).

Measure the resistance between DCM connector and chassis ground.

Connector & terminal

(i271) No. 4 — Chassis ground:

Is the resistance 1 M- or more-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A08 SOS BUTTON CIRCUIT

Repair or replace the open circuit of harness.

4.CHECK THE CONNECTOR (SHORT CIRCUIT TO POWER SUPPLY).

Measure the voltage between DCM connector and chassis ground.

Connector & terminal

(i270) No. 5 (+) — Chassis ground (−):
(AD2) No. 1 (+) — Chassis ground (−):

Is the voltage less than 1 V-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A08 SOS BUTTON CIRCUIT

Repair or replace the short circuit of the harness.

5.CHECK THE SOS BUTTON UNIT.

Measure the resistance of the SOS button unit.

Connector & terminal

(AD1) No. 6 — (AD1) No. 1:

Is the resistance 1 - or less when SOS button is ON, and 1.6 (±5%) k- or more when SOS button is OFF-

Replace the DCM. Data Communication Module

Replace the telematics button. Switches and Harness

Dtc b2a09 i-call button circuit
DIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:The following conditions occur for at least 50 ms.• i-button impedance is more than 10 k-.• i-button is stuck f ...

Dtc b2a06 right speaker/audio circuit
DIAGNOSIS START CONDITION:When ACC is ON.DTC DETECTING CONDITION:Speaker impedance is more than 10 k- for 100 mS. (Detached speaker connection, etc.)TROUBLE SYMPTOM:• Call function cannot be use ...

Other materials:

Ignition switch (models without pushbutton start system)
WARNING  Never turn the ignition switch to "LOCK" while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer. ...

© 2017-2024 Copyright www.sulegacy.com