Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc c1362 normal closing valve 2

Subaru Legacy BN/BS (2015-2019) Service Manual / Vehicle dynamics control (vdc) (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc c1362 normal closing valve 2

DTC DETECTING CONDITION:

A fault is detected if electrical malfunction judgment is generated for VDCH/U solenoid valve.

TROUBLE SYMPTOM:

• ABS does not operate.

• EBD does not operate.

• VDC does not operate.

• Hill hold does not function.

• EyeSight does not operate. (Models with EyeSight)

WIRING DIAGRAM:

Vehicle dynamics control system Vehicle Dynamics Control System

STEP	CHECK	YES	NO
1.CHECK VDCCM&H/U INPUT VOLTAGE. 1) Turn the ignition switch to OFF. 2) Disconnect the connector from the VDCCM&H/U. 3) Run the engine at idle. 4) Measure the voltage between VDCCM&H/U connector and chassis ground. Connector & terminal (B310) No. 5 (+) — (B310) No. 46 (−): (B310) No. 16 (+) — (B310) No. 46 (−): (B310) No. 33 (+) — (B310) No. 46 (−):	Is the voltage 10 — 15 V-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1362 NORMAL CLOSING VALVE 2	Repair the power supply circuit.
2.CHECK VDCCM&H/U GROUND CIRCUIT (CHECK FOR OPEN CIRCUIT). 1) Turn the ignition switch to OFF. 2) Measure the resistance between VDCCM&H/U connector and chassis ground. Connector & terminal (B310) No. 46 — Chassis ground:	Is the resistance less than 10 --	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1362 NORMAL CLOSING VALVE 2	Repair the VDCCM&H/U ground harness.
3.CHECK POOR CONTACT OF CONNECTORS.	Is there poor contact of connector between generator, battery and VDCCM&H/U-	Repair the connector.	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1362 NORMAL CLOSING VALVE 2
4.CHECK VDCCM&H/U. 1) Connect all connectors. 2) Perform the Clear Memory Mode. Clear Memory Mode 3) Perform the Inspection Mode. Inspection Mode 4) Read the DTC. Read Diagnostic Trouble Code (DTC)	Is the same DTC displayed-	Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1362 NORMAL CLOSING VALVE 2
5.CHECK DETECTION OF OTHER DTCS FOR VDC. Read Diagnostic Trouble Code (DTC)	Is any other DTC displayed-	Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)	Currently, it is normal. There may have been a poor contact in the harness and connector or a temporarily noise interference.

Dtc c1411 electrical control module

DTC DETECTING CONDITION:• Judge as malfunction when ECM internal malfunction is detected.• This malfunction is stored if the fluid pressure request from the electronic parking brake does n ...

Dtc c1361 normal closing valve 1

NOTE:For the diagnostic procedure, refer to “DTC C1362 NORMAL CLOSING VALVE 2 MALFUNCTION”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1362 NORMAL CLOSING VALVE 2 ...

Other materials:

Installation
1. Clean the mating surface of transmission case and converter case.2. Select the reduction gear shim. Reduction Drive Gear > ADJUSTMENT3. Remove the transmission case, and install the selected reduction gear shim to the reduction drive gear.4. Install the O-rings to the reverse clutch housing and ...