Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc p0335 crankshaft position sensor "a" circuit

DTC DETECTING CONDITION:

Immediately at fault recognition

TROUBLE SYMPTOM:

Engine stalls.

Failure of engine to start

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.

WIRING DIAGRAM:

Engine Electrical System ENGINE TYPE FB (WITHOUT PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM

Engine Electrical System ENGINE TYPE FB (WITH PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK INSTALLATION CONDITION OF CRANKSHAFT POSITION SENSOR.

Is the crankshaft position sensor installation bolt tightened securely-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0335 CRANKSHAFT POSITION SENSOR "A" CIRCUIT

Tighten the crankshaft position sensor installation bolt securely. Crankshaft Position Sensor > INSTALLATION

2.CHECK CRANKSHAFT POSITION SENSOR.

1) Turn the ignition switch to OFF.

2) Remove the crankshaft position sensor.

3) Measure the resistance between terminals of crankshaft position sensor.

Terminals

No. 1 — No. 2:

Is the resistance between 1 and 4 k--

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0335 CRANKSHAFT POSITION SENSOR "A" CIRCUIT

Replace the crankshaft position sensor. Crankshaft Position Sensor

3.CHECK HARNESS BETWEEN ECM AND CRANKSHAFT POSITION SENSOR CONNECTOR.

1) Disconnect the connector from ECM.

2) Measure the resistance of harness between ECM connector and crankshaft position sensor connector.

Connector & terminal

(E158) No. 40 — (E10) No. 1:

(E158) No. 27 — (E10) No. 2:

Is the resistance less than 1 --

Repair the poor contact of ECM and crankshaft position sensor connector.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

Open circuit in harness between ECM connector and crankshaft position sensor connector

Poor contact of coupling connector

1. OUTLINE OF DIAGNOSIS

Detect the open or short circuit of the crankshaft position sensor.

Judge as NG when the crank signal is not input even though the starter was rotated.

2. COMPONENT DESCRIPTION

(A)

Camshaft signal (RH)

(B)

Camshaft signal (LH)

(C)

Crankshaft signal

(1)

Crankshaft position sensor

(2)

Crankshaft position sensor plate

(3)

One crankshaft rotation

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

Battery voltage

≥ 8 V

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Number of crankshaft position sensor signals during cranking

= 0

Time Needed for Diagnosis: 3000 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0336 crankshaft position sensor "a" circuit range/performance
DTC DETECTING CONDITION:Detected when two consecutive driving cycles with fault occur.TROUBLE SYMPTOM:• Engine stalls.• Failure of engine to startCAUTION:After servicing or replacing fault ...

Dtc p0328 knock/combustion vibration sensor 1 circuit high bank 1 or single sensor
DTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:• Poor driving performance• Knocking occursCAUTION:After servicing or replacing faulty parts, perform Clear Memory M ...

Other materials:

Assembly
1. RADIATOR MAIN FAN AND RADIATOR MAIN FAN MOTOR1. Install the radiator main fan motor to the radiator fan shroud.Tightening torque:3.9 N·m (0.4 kgf-m, 2.9 ft-lb)2. Install the radiator main fan to the radiator main fan motor.Tightening torque:6.4 N·m (0.7 kgf-m, 4.7 ft-lb)3. Install t ...

© 2017-2024 Copyright www.sulegacy.com