Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc p0842 transmission fluid pressure sensor/switch "a" circuit low

DTC DETECTING CONDITION:

Immediately at fault recognition

TROUBLE SYMPTOM:

Shift characteristics malfunction

1. ENGINE TYPE FB

WIRING DIAGRAM:

CVT control system CVT Control System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK INPUT SIGNAL FOR TCM.

1) Start the engine.

2) Warm up until the ATF temperature reaches to 40 — 70°C (104 — 158°F).

3) Depress the brake pedal, and shift the select lever to “D” range.

4) Shift the select lever to “P” range.

5) Stabilize the engine speed at idle.

6) Read the data of «Actual secondary pressure» using Subaru Select Monitor.

Is the «Actual secondary pressure» 0.5 — 1.5 MPa-

Check for poor contact of connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

2.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the connector of TCM and secondary pressure sensor.

3) Measure the resistance between TCM connector and secondary pressure sensor connector.

Connector & terminal

(T10) No. 2 — (AT6) No. 3:

(T10) No. 5 — (AT6) No. 2:

(T10) No. 33 — (AT6) No. 1:

Is the resistance less than 1 --

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the open circuit of harness.

3.CHECK HARNESS.

Measure the resistance between TCM connector and chassis ground.

Connector & terminal

(T10) No. 5 — Chassis ground:

(T10) No. 33 — Chassis ground:

Is the resistance 1 M- or more-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the short circuit of harness.

4.CHECK POWER SUPPLY FOR SECONDARY PRESSURE SENSOR.

1) Connect the TCM connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between secondary pressure sensor connector terminals.

Connector & terminal

(AT6) No. 1 (+) — (AT6) No. 3 (−):

Is the voltage 4.5 V or more-

Replace the secondary pressure sensor. Secondary Pressure Sensor If the replacement of the sensor do not eliminate the malfunction, replace the TCM. Transmission Control Module (TCM)

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)

2. ENGINE TYPE EZ

WIRING DIAGRAM:

CVT control system CVT Control System > WIRING DIAGRAM

STEPCHECKYESNO

1.CHECK INPUT SIGNAL FOR TCM.

1) Start the engine.

2) Warm up until the ATF temperature reaches to 40 — 70°C (104 — 158°F).

3) Depress the brake pedal, and shift the select lever to “D” range.

4) Shift the select lever to “P” range.

5) Stabilize the engine speed at idle.

6) Read the data of «Actual secondary pressure» using Subaru Select Monitor.

Is the «Actual secondary pressure» 0.5 — 1.5 MPa-

Check for poor contact of connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

2.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM and transmission connectors.

3) Measure the resistance between TCM connector and transmission connectors.

Connector & terminal

(B54) No. 2 — (B22) No. 18:

(B54) No. 5 — (B22) No. 14:

(B54) No. 33 — (B22) No. 17:

Is the resistance less than 1 --

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the open circuit of harness.

3.CHECK HARNESS.

Measure the resistance between TCM connector and chassis ground.

Connector & terminal

(B54) No. 5 — Chassis ground:

(B54) No. 33 — Chassis ground:

Is the resistance 1 M- or more-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the short circuit of harness.

4.CHECK TRANSMISSION HARNESS.

1) Disconnect the secondary pressure sensor connector.

2) Measure the resistance between transmission connector and secondary pressure sensor connector.

Connector & terminal

(T4) No. 14 — (AT6) No. 2:

(T4) No. 17 — (AT6) No. 1:

(T4) No. 18 — (AT6) No. 3:

Is the resistance less than 1 --

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the open circuit of harness.

5.CHECK TRANSMISSION HARNESS.

Measure the resistance between transmission connector and chassis ground.

Connector & terminal

(T4) No. 14 — Chassis ground:

(T4) No. 17 — Chassis ground:

Is the resistance 1 M- or more-

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

Repair the short circuit of harness.

6.CHECK POWER SUPPLY FOR SECONDARY PRESSURE SENSOR.

1) Connect the connectors of TCM and transmission.

2) Turn the ignition switch to ON.

3) Measure the voltage between secondary pressure sensor connector terminals.

Connector & terminal

(AT6) No. 1 (+) — (AT6) No. 3 (−):

Is the voltage 4.5 V or more-

Replace the secondary pressure sensor. Secondary Pressure Sensor If the replacement of the sensor do not eliminate the malfunction, replace the TCM. Transmission Control Module (TCM)

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)

3. OUTLINE OF DIAGNOSIS

Detect the ground short circuit of the transmission line pressure sensor.

Judge as NG if the voltage detected by the transmission line pressure sensor is lower than the predetermined value.

4. EXECUTION CONDITION

Secondary Parameters

Execution condition

12 V battery system voltage

≥ 9 V

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Measured line pressure sensor input voltage

< 0.195 V

(Line pressure)

(< − 574 kPa)

Time Needed for Diagnosis: 0.5 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0843 transmission fluid pressure sensor/switch "a" circuit high
DTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:Shift characteristics malfunction1. ENGINE TYPE FBWIRING DIAGRAM:CVT control system CVT Control System > WIRING DIAGRAMSTEPCHEC ...

Dtc p0801 reverse inhibit control circuit/open
DTC DETECTING CONDITION:Immediately at fault recognitionNOTE:For diagnostic procedures, refer to “BODY CONTROL SYSTEM (DIAGNOSTICS)”. Diagnostic Procedure with Diagnostic Trouble Code (DT ...

Other materials:

Inspection
1. Measure the resistance between connector terminals.Preparation tool:Circuit testerTerminal No.Inspection conditionsStandard6 — 8Switch OFF1 M- or moreSwitch ONLess than 1 -2. Apply battery voltage between the connector terminals to check lighting condition of illumination inside the switch.Term ...

© 2017-2024 Copyright www.sulegacy.com