DTC DETECTING CONDITION: Immediately at fault recognition TROUBLE SYMPTOM: • Improper idling • Poor driving performance CAUTION: After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE. WIRING DIAGRAM: • Engine Electrical System ENGINE TYPE FB (WITHOUT PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM • Engine Electrical System ENGINE TYPE FB (WITH PUSH BUTTON START) Engine Electrical System > WIRING DIAGRAM STEP | CHECK | YES | NO | 1.CHECK ACCELERATOR PEDAL POSITION SENSOR OUTPUT. 1) Turn the ignition switch to ON. 2) Measure the voltage between ECM connector and chassis ground. Connector & terminal Main accelerator pedal position sensor signal (E134) No. 29 (+) — Chassis ground (−): Sub accelerator pedal position sensor signal (E134) No. 31 (+) — Chassis ground (−): | Is the difference in measured values for the main accelerator pedal position sensor signal and the sub accelerator pedal position sensor signal 0 V- | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2138 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D"/"E" VOLTAGE CORRELATION | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2138 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D"/"E" VOLTAGE CORRELATION | 2.CHECK ACCELERATOR PEDAL POSITION SENSOR OUTPUT. 1) Measure the voltage between accelerator pedal position sensor connector and chassis ground. Connector & terminal (B315) No. 6 (+) — Chassis ground (−): (B315) No. 3 (+) — Chassis ground (−): | Is the difference in measured values for the main accelerator pedal position sensor signal and the sub accelerator pedal position sensor signal 0 V- | Replace the accelerator pedal. Accelerator Pedal | Repair the harness and connector. NOTE: In this case, repair the following item: • Open circuit of harness between ECM connector and accelerator pedal position sensor connector • Short circuit to ground in harness between ECM connector and accelerator pedal position sensor connector | 3.CHECK HARNESS BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR CONNECTOR. Measure the resistance of harness between accelerator pedal position sensor connector and chassis ground. Connector & terminal (B315) No. 5 — Chassis ground: (B315) No. 2 — Chassis ground: | Is the resistance less than 5 -- | Repair the poor contact of ECM connector. | Repair the harness and connector. NOTE: In this case, repair the following item: • Open circuit of harness between ECM connector and accelerator pedal position sensor connector • Open circuit of harness between ECM connector and engine ground • Poor contact of ECM connector • Poor contact of joint connector |
1. OUTLINE OF DIAGNOSIS Judge as NG when the signal level of accelerator pedal position sensor 1 is different from the accelerator pedal position sensor 2. 2. COMPONENT DESCRIPTION (1) | Engine control module (ECM) | (3) | Accelerator pedal position sensor 2 signal | (4) | Accelerator pedal position sensor | (2) | Accelerator pedal position sensor 1 signal | | | | |
3. EXECUTION CONDITION Secondary Parameters | Execution condition | Battery voltage | ≥ 6 V |
4. GENERAL DRIVING CYCLE Always perform the diagnosis continuously. 5. DIAGNOSTIC METHOD If the duration of time while the following conditions are met is longer than the time indicated, judge as NG. Judgment ValueMalfunction Criteria | Threshold Value | Signal difference between two sensors | Within NG range of Details of Judgment value | Details of Judgment Value (X1) | 0.6 ° | (X2) | 1.2 ° | (X3) | 2 ° | (X4) | 4 ° | | | | | | | | | | | (Y1) | 1.465 ° | (Y2) | 1.597 ° | (Y3) | 1.663 ° | (Y4) | 2.455 ° | (Y5) | 3.116 ° | | |
Time Needed for Diagnosis: 116 ms Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs. |