Subaru Legacy BN/BS (2015-2019) Service Manual: Eyesight (diagnostics)
Subaru Legacy BN/BS (2015-2019) Service Manual / Eyesight (diagnostics)
- Basic diagnostic procedure procedure
- Check list for interview check
- Clear active lane keep system learning value operation
- Clear memory mode operation
- Electrical component location location
- Real-time diagnosis operation
- Acc cancel code(s) display
- Active lane keep system code(s) display
- Control module i o signal
- Diagnostic code(s) display
- Diagnostic procedure with diagnostic trouble code (dtc)
- Dtc u0428 invalid data received from steering angle sensor module
- Dtc u0100 lost communication with ecm/pcm "a"
- Dtc u0073 control module communication bus off
- Dtc u0423 invalid data received from instrument panel cluster control module
- Dtc u0422 invalid data received from body control module
- Dtc u0420 invalid data received from power steering control module
- Dtc u0416 invalid data received from vehicle dynamics control module
- Dtc u0402 invalid data received from tcm
- Dtc u0401 invalid data received from ecm/pcm "a"
- Dtc u0155 lost communication with instrument panel cluster (ipc) control module
- Dtc b28ba steering angle and stereo camera correlation misaligned
- Dtc b28b9 eyesight steering switch 2
- Dtc b28b8 eyesight steering switch 1
- Dtc b28b7 ldp off switch
- Dtc b28b6 pre-collision off switch
- Dtc b28b5 +b circuit open
- Dtc b28b3 stereo camera low temperature
- Dtc b28b2 stereo camera high temperature
- Dtc b28b1 stereo camera automatic adjustment
- Dtc b28af stereo camera adjustment incomplete
- Dtc b28ae internal stereo camera power supply
- Dtc b28ad stereo camera image recognition
- Dtc b28ac stereo camera asic
- Dtc b28ab stereo camera microcomputer 2
- Dtc b28aa stereo camera microcomputer 1
- Dtc b28a9 stereo camera synchronized recognition data
- Dtc b28a8 internal stereo camera communication 2
- Dtc b28a7 stereo camera recognition(target)
- Dtc b28a6 internal stereo camera communication 1
- Dtc b28a5 engine torque limiter control prohibit
- Dtc b28a4 eyesight communication(eps)
- Dtc b28a3 eyesight communication(meter)
- Dtc b28a2 eyesight communication(vdc)
- Dtc b28a1 eyesight communication(ecm)
- Dtc b28a0 vehicle model judgment
- Dtc b281c incompatible with eyesight (eps)
- Dtc b281b steering angle sensor fail
- Dtc b2817 brake lamp
- Dtc b2815 power supply high voltage
- Dtc b2814 power supply low voltage
- Dtc b2811 eps abnormal
- Dtc b2810 incompatible with eyesight (combination meter)
- Dtc b280f combination meter malfunction
- Dtc b280c vdc brake control prohibit
- Dtc b280b vdc brake fluid pressure
- Dtc b280a vdc echo back disagreement
- Dtc b2809 vdc malfunction
- Dtc b2807 ecm abnormal
- Dtc b2806 ecm abnormal
- Dtc b2804 epb no activity detected
- Dtc b2803 epb operation prohibit
- Dtc u0140 lost communication with body control module
- Dtc u0131 lost communication with power steering control module
- Dtc u0126 lost communication with steering angle sensor module
- Dtc u0122 lost communication with vehicle dynamics control module
- Dtc b2802 etc abnormal
- Dtc b2801 tcm abnormal
- Dtc u0101 lost communication with tcm
- Diagnostics with phenomenon
- Check adaptive cruise control indicator light/constant speed cruise control indicator light and cruise set indicator light
- Check eyesight steering switch
- Ecm cancel code(s) display
- Eyesight temporary code(s) display
- Freeze frame data display
- General description
- Subaru select monitor
Installation
CAUTION:• When reusing the tether clip on the upper part of the trim panel - front pillar UPR, check that there is no damage to the tether clip. If the tether clip is damaged, always replace it ...
Basic diagnostic procedure procedure
CAUTION:• Start the diagnosis after the engine has started. (Cruise control main switch does not turn on even if it is pressed before the engine starts.)• When performing diagnosis, observ ...
Other materials:
Installation
1. Remove the front differential assembly.2. Hypoid gear set match mark/No.: The number (A) on top of the drive pinion, and the number on the hypoid driven gear are set numbers for the two gears. Use a pair having the same numbers.The figure (B) below shows a number for shim adjustment. If no number ...
© 2017-2025 Copyright www.sulegacy.com
