Subaru Legacy BN/BS (2015-2019) Service Manual: Installation
1. REAR GATE PANEL CAUTION: The panel - rear gate is heavy. When removing and installing it, always work in a team of two or more persons. 1. Install the hinge - rear gate to the vehicle body. 2. Temporarily install the panel - rear gate to the hinge - rear gate. NOTE: When installing, make sure that a uniform clearance is created around the panel - rear gate. 3. Adjust the clearance around the panel - rear gate. Rear Gate > ADJUSTMENT 4. Tighten the bolts of the hinge - rear gate. Tightening torque: 25 N·m (2.5 kgf-m, 18.4 ft-lb) 5. Install the stay assembly - rear gate. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT 6. Install the harness clip and the harness. 7. Install the light assembly - rear finisher. Rear Finisher Light Assembly > INSTALLATION Tightening torque: 4.5 N·m (0.5 kgf-m, 3.3 ft-lb) 8. Install the license plate light. License Plate Light > INSTALLATION 9. Install the rearview camera assembly. Rearview Camera System > INSTALLATION 10. Install the rear gate garnish. Rear Gate Garnish > INSTALLATION Tightening torque: 4.5 N·m (0.5 kgf-m, 3.3 ft-lb) 11. Install the nozzle - rear washer. 12. Install the roof spoiler. Rear Gate Garnish > INSTALLATION Tightening torque: 7.5 N·m (0.8 kgf-m, 5.5 ft-lb) 13. Install the antenna assembly - radio. Tightening torque: 4.5 N·m (0.5 kgf-m, 3.3 ft-lb) 14. Install the power rear gate touch sensor. (Model with power rear gate) Power Rear Gate Touch Sensor > INSTALLATION 15. Install the motor assembly - rear wiper and the arm assembly - rear wiper. Rear Wiper Motor > INSTALLATION Tightening torque: Motor assembly - rear wiper and arm assembly - rear wiper: General Description > COMPONENT 16. Install the rear antenna assembly - exterior. (Model with keyless access with push button start) 17. Attach the buffer - rear gate and the stopper - rear gate. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT 18. Install the latch and actuator - rear gate. Rear Gate Latch and Actuator Assembly > INSTALLATION Tightening torque 25 N·m (2.5 kgf-m, 18.4 ft-lb) 19. Install the trim panel - rear gate. Rear Gate Trim > INSTALLATION 20. Install the rod - power rear gate. Power Rear Gate Rod > INSTALLATION 21. Connect the ground terminal to battery sensor. NOTE 2. REAR GATE DAMPER STAY CAUTION: The panel - rear gate is heavy. When removing and installing it, always work in a team of two or more persons. 1. Prevent the panel - rear gate from closing using prop or the like. CAUTION: If the prop comes off, operators may get injured and vehicle may get damaged. Make sure to support the panel - rear gate with secure material to prevent injury or damage.
2. Install the stay assembly - rear gate. Tightening torque: Refer to “COMPONENT” of “General Description”. General Description > COMPONENT |
Adjustment
Adjust the clearance around the panel - rear gate as follows.PartStandardAPanel - rear gate to Roof panel6.6+1.5, −1.0 mm (0.26+0.06, −0.04 in)BSurface level gap: Panel - rear gate to Roof ...
Disposal
1. REAR GATE DAMPER STAYCAUTION:Gas is colorless, odorless, and harmless. However, gas pressure may spray cutting powder or oil. Be sure to wear dust-resistant goggles.1. Cover with a vinyl sack as sh ...
Other materials:
Dtc c2521 speed abnormal
DTC DETECTING CONDITION:Detected when transmitter normal signal is received at a vehicle speed of less than 6 km/h (4 MPH).TROUBLE SYMPTOM:Tire pressure warning light blinks 25 times and then illuminates.WIRING DIAGRAM:NOTE:For the coupling connector, refer to “WIRING SYSTEM”.Tire Pressu ...
