Honda Civic manuals

Subaru Legacy Service Manual: Installation

NOTE:

Use the markings on the glass to apply adhesive and primer, and to install the dam rubber - rear gate and the spacer - rear gate.

(a)

Locating pin - rear gate

(d)

Marking for dam rubber - rear gate application (Ag print)

(g)

Adhesive application area

(b)

Holder - rear gate upper

(e)

Origin of attachment

(h)

Spacer - rear gate

(c)

Dam rubber - rear gate

(f)

Adhesive line

(i)

Molding - rear gate side (model without power rear gate)

1. Fabricate the cartridge nozzle tip as shown and set the sealant gun with the adhesive.

(a)

10 mm (0.39 in)

(b)

8 mm (0.31 in)

(c)

Sealant gun

2. Smoothen and clean the adhesive surfaces of the glass - rear gate and body using the same procedures as for the glass - front window. Windshield Glass > INSTALLATION

3. Attach the dam rubber - rear gate to the glass - rear gate.

(a)

Dam rubber - rear gate

(c)

Spacer - rear gate

(e)

Molding - rear gate side (model without power rear gate)

(b)

Locating pin - rear gate

(d)

Holder - rear gate upper

4. Attach the molding - rear gate side to the glass - rear gate. (Model without power rear gate)

CAUTION:

Be careful to attach the molding - rear gate side so that the molding has no loose or undulating part.

NOTE:

Install the molding - rear gate side so that its upper end is within (b).

Use the Ag print as a reference when installing the molding - rear gate side.

(a)

Glass - rear gate

(d)

13.7 mm (0.54 in)

(g)

Molding - rear gate side

(b)

10 mm (0.39 in)

(e)

11.7 mm (0.46 in)

(c)

Marking for molding - rear gate side application (Ag print)

(f)

Double-sided tape

5. Install the glass - rear gate.

(1) Apply the primer to the adhesive surface of glass - rear gate side and body side using sponge.

(2) Apply adhesive to the glass - rear gate end back surface.

CAUTION:

Do not apply primer to adhesive.

(a)

Application of primer (glass side)

(b)

Application of primer (body side)

(c)

Adhesive

(3) Attach the holder - clip rear gate to the holder - rear gate upper of the glass - rear gate.

(4) Insert the locating pins - rear gate into the rear gate panel holes, and install the glass - rear gate.

(5) Lightly press the entire perimeter of the glass - rear gate for tight fit.

(6) Make flush the adhesive surface jutted out using spatula.

6. After completion of all work, allow the vehicle to stand for about 24 hours.

NOTE:

When opening/closing the door after the glass - rear gate was bonded, always lower the glass assembly - door first, and then open/close it carefully.

Move the vehicle slowly.

For minimum drying time and vehicle standing time before driving after bonding, follow instructions or instruction manual from the adhesive manufacturer.

7. Connect the rear defogger connector.

8. Install the motor assembly - rear wiper and the arm assembly - rear wiper. Rear Wiper Motor > INSTALLATION

Tightening torque:

Motor assembly - rear wiper and arm assembly - rear wiper: General Description > COMPONENT

9. Install the roof spoiler. Rear Gate Garnish > INSTALLATION

Tightening torque:

7.5 N·m (0.8 kgf-m, 5.5 ft-lb)

10. Install the touch sensor LWR. Power Rear Gate Touch Sensor > INSTALLATION

11. Install the trim panel - rear gate. Rear Gate Trim > INSTALLATION

12. Connect the ground terminal to battery sensor. NOTE

13. After curing of adhesive, pour the water on external surface of vehicle to check that there are no water leaks.

NOTE:

When a vehicle is returned to the user, tell him or her that the vehicle should not be subjected to heavy impact for at least three days.

Removal
1. Disconnect the ground terminal from battery sensor. NOTE2. Remove the roof spoiler. Roof Spoiler > REMOVAL3. Remove the trim panel - rear gate and the motor assembly - rear wiper. Rear Wiper Mot ...

Rear quarter glass
...

Other materials:

Dtc p0452 evap system (cpc) pressure sensor/switch circuit low
DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.WIRING DIAGRAM:• Engine Electrical System ENGINE TYPE FB (WITHOUT PUSH BUTTON ST ...

© 2017-2022 Copyright www.sulegacy.com