Honda Civic manuals

Subaru Legacy BN/BS (2015-2019) Service Manual: User customizing operation

1. On «Start» display, select «Diagnosis».

2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».

3. On «Main Menu» display, select «Each System».

4. On «Select System» display, select «Body Control» and then select «Enter».

5. On «Select Function» display, select «Customize».

NOTE:

If not equipped (depending on destination area or vehicle equipment condition), customizing is not possible.

For detailed operation procedures, refer to “Application help”.

List of User Customizing item

Item

Initial setting value

Setting value

Note

Off delay time

30 Sec

OFF

10 Sec

20 Sec

30 Sec

Room light off delay time can be selected.

Auto Light Sensitivity Adjustment

Sensitive

Dull

Normal

Sensitive

Very sensitive

Sensitivity of the automatic lighting can be adjusted.

Lane change signal setting

ON

ON

OFF

ON: One-touch blinker function operates.

OFF: One-touch blinker function does not operate.

Rear wiper auto setting

OFF (U0, U4, U5 models)

ON: (C0, C5 models)

ON

OFF

ON: Rear wiper operates in sync with the reverse shift.

OFF: Rear wiper does not operate in sync with the reverse shift.

Driver’s Door Unlock Setting

Selection

Selection

ALL

Selection: When the touch sensor (unlock) on the driver’s side is touched, only the driver’s door is unlocked. When the touch sensor (unlock) on the passenger’s side is touched, all doors are unlocked.

ALL: When the touch sensor (unlock) on the driver’s side is touched, all doors are unlocked. When the touch sensor (unlock) on the passenger’s side is touched, all doors are unlocked.

Rear Gate Unlock Setting

Selection

Selection

ALL

Selection: When the rear gate opener button is pressed, only the rear gate is unlocked.

ALL: When the rear gate opener button is pressed, all doors are unlocked.

Wiper link Auto Light Setup

ON

ON

OFF

ON: Wiper interlock auto light function is activated.

OFF: Wiper interlock auto light function is deactivated.

High Beam Assist Function

(*1)

ON

OFF

Set to ON for models with high beam assist.

Head Lamp Low Beam Specification

(*1)

Halogen

HID

LED

Set according to the headlight type.

Head Lamp High Beam Specification

(*1)

Halogen

HID

LED

Set according to the headlight type.

High Beam Assist Current Setting

(*1)

ON

OFF

Set to ON for models with high beam.

Rear defogger operation mode

Normal

Normal

Continuous

Normal: Automatically stops in 15 minutes after the switch is turned to ON.

Continuous: Repeats the cycle of 15-minute active condition and 2-minute inactive condition until the switch is turned to OFF.

Security Alarm Setup

ON

ON

OFF

ON: Warning function (hazard, horn) is activated.

OFF: Warning function (hazard, horn) is deactivated.

Impact Sensor Setup

ON

ON

OFF

ON: Impact sensor is activated.

OFF: Impact sensor is deactivated. (Set to “OFF” in models without the impact sensor.)

Alarm delay setup

ON

ON

OFF

ON: The alarm monitor starts 30 seconds after the keyless lock operation.

OFF: The alarm monitor starts immediately after the keyless lock operation.

Lockout prevention

ON

ON

OFF

ON: Key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.)

OFF: Key lockout prevention function is deactivated.

Impact sensor

OFF

ON

OFF

ON: Vehicle is controlled in impact sensor equipped mode. (Make sure to set to “OFF” for models without the impact sensor. When set to “ON”, hazard, horn or siren become activated by keyless lock (alarm monitor start).)

OFF: Vehicle is controlled in no impact sensor mode.

Buzzer sounding setting

ON

ON

OFF

ON: Buzzer sounds when lock/unlock is selected by keyless entry system.

OFF: Buzzer does not sound when lock/unlock is selected by keyless entry system.

Abnormal warning lamp flashing setting

ON

ON

OFF

ON: Hazard blinks when lock/unlock is selected by keyless entry system.

OFF: Hazard does not blink when lock/unlock is selected by keyless entry system.

Initial keyless setting

Execution

Initial button setting

Execution

Initial Security setting

Execution

Door open warning

ON

ON

OFF

ON: If a door stays half shut for 20 minutes, interior lighting linked with the door such as room light, map light, luggage room light, trunk room light and key ring illumination go off to prevent battery run-out.

OFF: Room light, map light, luggage room light, trunk room light, key ring illumination and door warning light remain lit.

Dome Light Alarm Setting

OFF

ON

OFF

ON: Room light illumination is interlocked with the alarm.

OFF: Room light illumination is not interlocked with the alarm.

Welcome Light (Exit)

30 Sec

OFF

30 Sec

60 Sec

90 Sec

Lighting time length of the welcome lighting (exiting) function can be set.

Welcome Light Off Delay Time(Approaching)

30 Sec

OFF

30 Sec

60 Sec

90 Sec

Lighting time length of the welcome lighting (approaching) function can be set.

Keyless Buzzer Volume

5

1 — 7

Buzzer volume can be set.

Auto Dimmer Cancel setting

3

0 (OFF)

Least

2

Normal

4

Most

Auto dimmer cancel sensitivity can be set.

NOTE:

*1: Customization item according to the actual vehicle equipment

6. When the setting is complete, see «Data monitor» to make sure that the alterations are consistent with the actual equipment on the vehicle.

CAUTION:

the above settings must match the actual vehicle equipment.

Do not change settings except for setting above while setting the functions.

Be sure not to change Factory initial setting except when installing a new body integrated unit.

Subaru select monitor operation
• For detailed operation procedures, refer to “Application help”.• When communication with Subaru Select Monitor is not possible, perform “COMMUNICATION FOR INITIALIZING ...

Diagnostic procedure with diagnostic trouble code (dtc)
...

Other materials:

Electrical specification
CAUTION:Never remove the occupant detection control module, occupant detection sensor or seat frame because they are integrated into one unit.Terminal No.Description1Belt tension sensor output2Belt tension sensor power supply3GND4Seat belt buckle switch output5LIN communication line (airbag CM)6Igni ...

© 2017-2024 Copyright www.sulegacy.com