Honda Civic manuals

Subaru Legacy Service Manual: Preparation tool

1. SPECIAL TOOL

ILLUSTRATION

TOOL NUMBER

DESCRIPTION

REMARKS

41099AJ010

SPECIAL TOOL H6

Used for removing and installing transmission.

For H6 engine.

18360AA020

HANGER

Used for removing and installing transmission.

For H6 engine.

18801AA000

OIL PRESSURE GAUGE ASSY

Used for measuring the secondary pressure (line pressure).

18658AA020

WRENCH COMPL RETAINER

Used for removing and installing the differential side retainer.

18681AA000

PRESSURE GAUGE ADAPTER

Used for measuring the secondary pressure (line pressure) and transfer clutch hydraulic pressure.

NOTE:

Used together with the genuine O-ring (part No. 806911080).

18769AA000

EXPANDER PULLEY

Used for removing and installing the secondary pulley assembly.

99099AJ000

ENGINE HANGER

Used for removing and installing the automatic transmission assembly.

Used together with CHAIN BALANCER (99099AJ010).

99099AJ010

CHAIN BALANCER

Used for removing and installing the automatic transmission assembly.

Used together with ENGINE HANGER (99099AJ000).

498897700

OIL PRESSURE ADAPTER SET

Used for measuring the secondary pressure (line pressure) hydraulic pressure.

34099AC020

ADAPTER HOSE B

Used for measuring the transfer clutch hydraulic pressure.

NOTE:

Used with genuine union screw (Part No. 801914010) and gasket (Part No. 803914060).

34099AC010

ADAPTER HOSE A

Used for measuring the transfer clutch hydraulic pressure.

73099SG000

SPECIAL TOOL CONDENSER

Used for installing the transfer clutch pressure test plug.

18270AA040

SOCKET

Used for installing the transfer clutch pressure test plug.

498575400

OIL PRESSURE GAUGE ASSY

Used for measuring the transfer clutch hydraulic pressure.

498277200

STOPPER SET

Used for removing and installing automatic transmission assembly to engine.

Used for preventing the torque converter from dropping off.

398527700

PULLER ASSY

Used for removing the extension case oil seal.

Used for removing the roller bearing of the primary pulley and secondary pulley.

Used for removing the bearing of reduction driven gear.

Used for removing the differential side retainer bearing outer race.

18760AA000

CLAW

Used for removing ball bearing of front reduction driven gear.

Used together with PULLER ASSY (398527700).

498057300

INSTALLER

Used for installing the extension case oil seal.

18632AA000

TRANSMISSION STAND

Used for disassembling and assembling the transmission.

498255400

PLATE

Used for measuring the backlash of hypoid gear.

498247001

MAGNET BASE

Used for measuring the backlash of differential bevel pinion gear.

Used for measuring the backlash of hypoid gear.

Used for measuring the clearance in forward clutch.

Used together with DIAL GAUGE (498247100).

498247100

DIAL GAUGE

Used for measuring the backlash of differential bevel pinion gear.

Used for measuring the backlash of hypoid gear.

Used for measuring the clearance in forward clutch.

Used together with DIAL GAUGE (498247101).

18675AA000

DIFFERENTIAL SIDE OIL SEAL INSTALLER

Used for installing the differential side retainer oil seal.

18762AA001

COMPRESSOR SPECIAL TOOL

Used for disassembling and installing the multi-plate clutch piston for shifting.

COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.

18765AA000

COMPRESSOR SUPPORT

Used for disassembling and installing the multi-plate clutch for shifting.

18763AA000

COMPRESSOR SHAFT

Used for disassembling and installing the multi-plate clutch for shifting.

28399SA010

OIL SEAL PROTECTOR

Used for protecting oil seal when installing front drive shaft.

18667AA010

HOLDER

Used for removing and installing the drive pinion lock nut.

Used as a holder to rotate gear when checking tooth contact.

18270KA010

SOCKET (E16)

Used for removing and installing the center support COMPL.

18270KA020

SOCKET (E20)

Used for removing and installing the hypoid driven gear.

Used for removing and installing the drive pinion shaft retainer.

398497701

SEAT

Used for removing and installing the ball bearing.

398177700

INSTALLER

Used for removing and installing the ball bearing and tapered roller bearing.

Used for installing the parking gear.

398643600

GAUGE

Used for measuring the total end play, extension end play and drive pinion height.

899864100

REMOVER

Used for removing and installing the ball bearing.

498077000

REMOVER

Used for removing ball bearing of front reduction drive gear.

Used for removing the inner bearing inner race of the drive pinion shaft.

Used for removing the differential taper roller bearing.

18657AA010

INSTALLER

Used for installing the oil seal of inhibitor switch.

18657AA020

OIL SEAL INSTALLER

Used for installing the oil seal.

18621AA000

ADAPTER WRENCH

Used for removing and installing the drive pinion shaft lock nut.

18651AA000

INSTALLER

Used for installing the bearing of front reduction drive gear.

18720AA000

REMOVER

Used for removing ball bearing of reduction driven gear.

498497300

CRANKSHAFT STOPPER

Used for stopping the drive plate rotation when removing and installing the drive plate.

20299AG010

PRESS SNAP RING

Used for installing the bearing on primary pulley side.

399513600

INSTALLER

Used for removing the ball bearing of the rear drive shaft.

Used for removing the bearing of the oil pump chain sprocket.

499267300

STOPPER PIN

Used for adjusting the inhibitor switch.

499277100

BUSHING 1-2 INSTALLER

Used for installing the front differential taper roller bearing.

Used for removing and installing the transfer reduction drive gear.

Used for installing the ball bearing of the transfer reduction drive gear.

Used for installing the oil seal.

Used for installing the ball bearing of the transfer reduction driven gear.

499277200

INSTALLER

Used for installing the inner bearing inner race of drive pinion shaft.

Used for installing the reduction driven gear.

499575400

GAUGE

Used for measuring height of end play.

499737100

PULLER SET

Used for measuring height of forward clutch.

Used for measuring the transfer end play.

Use the rack only.

499575600

GAUGE

Used for measuring height of forward clutch.

Used for measuring height of end play.

499787700

WRENCH

Used for measuring the differential pinion shaft backlash.

499757002

INSTALLER

Used for installing the bearing of front reduction driven gear.

18767AA000

BEARING REMOVER

Used for removing the transfer reduction drive gear.

Used for removing the reduction driven gear bearing retainer.

Used for removing the front reduction driven shaft.

499755602

PRESS SNAP RING

Used for installing the oil seal.

Used for installing the ball bearing and roller bearing.

498077600

REMOVER

Used for removing the ball bearing of the rear drive shaft.

Used for removing the ball bearing of transfer reduction driven gear.

Used for removing ball bearing of reduction driven gear.

Used for removing the ball bearing of drive sprocket.

18460AA040

CHECK BOARD

Used for inspecting the TCM terminal.

(Newly adopted tool)

SUBARU SELECT MONITOR 4

Used for setting of each function and troubleshooting for electrical system.

NOTE:

For detailed operation procedures of Subaru Select Monitor 4, refer to “Application help”.

2. GENERAL TOOL

TOOL NAME

REMARKS

Circuit tester

Used for measuring resistance, voltage and current.

Thickness gauge

Used for the clearance in reverse brake, transfer clutch and input clutch.

Caliper

Used for measuring the clearance at the parts.

Spring scale

Used for measuring the starting torque of the drive pinion.

TORX® bit T70

Used for removing and installing differential gear oil drain plug.

Straight pin remover

Used for removing and installing the spring pin.

Deep socket

Used for removing and installing the secondary pressure sensor.

NOTE:

Use Ko-ken 3/8 12-point 27 mm (manufacturer product No. 3305M-27).

Push/pull gauge

Used for measuring clutch clearance.

Angle gauge

Used for installing the hypoid driven gear.

Used for installing the drive plate.

Chain sling

Used for removing and installing transmission.

Length: 0.8 — 1 m (2.6 — 3.3 ft)

Load capacity: 1.2 t (2646 lb) or more

Diameter: 6 mm (0.24 in) or 6.3 mm (0.25 in)

Chain external width: 23.5 mm (0.93 in) or less

Chain internal width: 8.5 mm (0.33 in) or more

Screw shackle

Used for removing and installing transmission.

Load capacity: 250 kg (551 lb) or more

Use two pieces.

DST-i

Used together with Subaru Select Monitor 4.

Caution
• Wear appropriate work clothing, including a cap, protective goggles and protective shoes when performing any work.• Remove contamination including dirt and corrosion before removal, inst ...

Inhibitor switch
...

Other materials:

Base display audio set (if equipped)
1) Power/VOLUME knob 2) Eject button 3) AUDIO/TUNE knob 4) HOME button 5) APPS button 6) Display 7) SEEK/TRACK buttons The audio set will operate only when the ignition switch is in the "ACC" or "ON" position.  Power and audio controls: refer to "Basic operation" .  SU ...

© 2017-2019 Copyright www.sulegacy.com