Subaru Legacy BN/BS (2015-2019) Service Manual: Dtc b2a01 lte1 antenna circuit

Subaru Legacy BN/BS (2015-2019) Service Manual / Telematics system (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc b2a01 lte1 antenna circuit

DIAGNOSIS START CONDITION:

When ignition switch is ON.

DTC DETECTING CONDITION:

Any of the followings continues for 5 seconds or more.

• LTE1 impedance is more than 1 M-. (Detached antenna, etc.)

• LTE1 impedance is less than 1 k-. (Short-circuited antenna, etc.)

TROUBLE SYMPTOM:

• Telematics function cannot be used.

• RED LED illuminates.

WIRING DIAGRAM:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Telematics Telematics System > WIRING DIAGRAM

CAUTION:

CommCheck is required after replacing the DCM. Telematics System > OPERATION

STEP	CHECK	YES	NO
1.CHECK DTC. Read the DTC. Diagnostic Code(s) Display	Is DTC B2A01 displayed- (Current malfunction)	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A01 LTE1 ANTENNA CIRCUIT	Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again. In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
2.CHECK HARNESS (OPEN CIRCUIT). 1) Turn the ignition switch to OFF. 2) Disconnect the antenna connector. 3) Disconnect the DCM connector. 4) Disconnect the PRG DU connector. 5) Measure the resistance between antenna connector and DCM connector. Connector & terminal OUTBACK model (AN41) No. 1 — (AN16) No. 3: Sedan model (AN41) No. 1 — (AN40) No. 1:	Is the resistance less than 1 --	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A01 LTE1 ANTENNA CIRCUIT	Repair or replace the open circuit of harness.
3.CHECK HARNESS (GROUND SHORT CIRCUIT). Measure the resistance between DCM connector and chassis ground. Connector & terminal (AN41) No. 1 — Chassis ground:	Is the resistance 1 M- or more-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A01 LTE1 ANTENNA CIRCUIT	Repair or replace the short circuit of the harness.
4.CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY). 1) Turn the ignition switch to ON. 2) Measure the voltage between DCM connector and chassis ground. Connector & terminal (AN41) No. 1 (+) — Chassis ground (−):	Is the voltage less than 1 V-	Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A01 LTE1 ANTENNA CIRCUIT	Repair or replace the short circuit of the harness.
5.CHECK ANTENNA. Check the telematics antenna. Antenna	Is the telematics antenna OK-	Replace the DCM. Data Communication Module	Replace the telematics antenna. Antenna

Dtc b2a02 lte2 antenna circuit

DIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:Any of the followings continues for 5 seconds or more.• LTE2 impedance is more than 1 M-. (Detached antenna, etc.)&bu ...

Dtc b2a00 vin reading

DIAGNOSIS START CONDITION:When ignition switch is ON.TROUBLE SYMPTOM:When ignition switch is ON, VIN information (CAN) sent from ECM cannot be read.DTC DETECTING CONDITION:• Telematics function ...

Other materials:

If you have accidentally triggered the alarm system
To stop the alarm Perform any of the following operations. Press any button on the access key/ remote transmitter. Turn the ignition switch to the "ON" position (models without "keyless access with push-button start system"). Turn the push-button ignition switch to ...