1.CHECK INSTALLATION OF VDCCM&H/U. | Is VDCCM&H/U installed properly without being tilted-
Is the bracket deformation-free-
Are the VDCCM&H/U installation bolts installed without missing or getting loose- | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR | Repair the defective part. • Install VDCCM&H/U properly. • Replace the bracket if faulty. • Tighten the VDCCM&H/U installation bolt. General Description > COMPONENT Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR |
2.CHECK OUTPUT OF STEERING ANGLE SENSOR USING SUBARU SELECT MONITOR. 1) Park the vehicle straight on a level surface. 2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION 3) Read the «Steering Angle Sensor» displayed on display. | Is the indicated reading of the steering angle sensor on the monitor display −10° — 10°- | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR | Check the installation of steering angle sensor. |
3.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR. 1) Park the vehicle straight on a level surface. 2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION 3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display. | Is the indicated reading of the lateral G sensor and longitudinal G sensor on the monitor display −2 — 2 m/s2- | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR | Recheck from step 1, and if the problem is not solved, go to next. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR |
4.SET 0 POINT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR. 1) Using the Subaru Select Monitor, select “Work Support”. 2) Perform the VDC sensor midpoint setting mode. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT | Is 0 point setting successful- | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR | Recheck from step 1, and when the 0 point setting is not possible, replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) |
5.PERFORM DRIVING TEST. Inspection Mode | Does the ABS warning light or VDC warning light illuminate during driving-
Does ABS or VDC operate abnormally- | Recheck from step 1, and when the warning lights illuminate or improperly operate, replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) | Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR |
6.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR. 1) Park the vehicle on a level surface. 2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION 3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display. | Is the indicated reading of the lateral G sensor and longitudinal G sensor on the monitor display −1.5 — 1.5 m/s2- | Currently, it is normal. There may have been a poor contact in the harness and connector or a temporarily noise interference. | Recheck from step 1, and if the problem is not solved, replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) |
7.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR. 1) Remove the VDCCM&H/U installation bolt and bracket. 2) Keep VDCCM&H/U in a horizontal position. 3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION 4) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display. | When the VDCCM&H/U is in a horizontal position, is the indicated reading of the lateral G sensor and longitudinal G sensor on the monitor display −1.5 — 1.5 m/s2- | Check the bracket and brake pipe, and install VDCCM&H/U in a horizontal position to the vehicle. | Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) |
Dtc c1733 longitudinal g sensor
Dtc c1721 yaw rate sensor