Subaru Legacy BN/BS (2015-2019) Service Manual: Installation
1. LOW-PRESSURE HOSE CAUTION: • If the hose and pipe has been replaced, add an appropriate amount of compressor oil to the compressor. Compressor Oil > ADJUSTMENT • Do not start the engine before charging refrigerant. • If the engine is started with no refrigerant charge, replace the compressor assembly. • Replace the O-rings with new parts, and then apply compressor oil. • When connecting hoses, do not apply an excessive force to them. After installing, check that no torsion or excessive tension applied to the hoses. 1. Install the hose - pressure suction. Tightening torque: Air conditioning unit: General Description > COMPONENT 2. Install the hose - pressure suction discharge. (H6 model) Tightening torque: 10 N·m (1 kgf-m, 7.4 ft-lb) 3. Connect the ground terminal to battery sensor. NOTE 4. Charge refrigerant. Refrigerant Charging Procedure > PROCEDURE 2. HIGH-PRESSURE HOSE CAUTION: • If the hose and pipe has been replaced, add an appropriate amount of compressor oil to the compressor. Compressor Oil > ADJUSTMENT • Do not start the engine before charging refrigerant. • If the engine is started with no refrigerant charge, replace the compressor assembly. • Replace the O-rings with new parts, and then apply compressor oil. • When connecting hoses, do not apply an excessive force to them. After installing, check that no torsion or excessive tension applied to the hoses. 1. Install the hose - pressure suction discharge. Tightening torque: Air conditioning unit: General Description > COMPONENT 2. Install the reservoir tank. Tightening torque: 7.5 N·m (0.8 kgf-m, 5.5 ft-lb) 3. Connect the ground terminal to battery sensor. NOTE 4. Charge refrigerant. Refrigerant Charging Procedure > PROCEDURE 3. A/C PIPE CAUTION: • If the hose and pipe has been replaced, add an appropriate amount of compressor oil to the compressor. Compressor Oil > ADJUSTMENT • Do not start the engine before charging refrigerant. • If the engine is started with no refrigerant charge, replace the compressor assembly. • Replace the O-rings with new parts, and then apply compressor oil. • When connecting pipes, do not apply an excessive force to them. After installation, check that the pipes are not damaged. 1. Install the pipe - evaporator cooling. Tightening torque: 7.5 N·m (0.8 kgf-m, 5.5 ft-lb) 2. Install the hose - pressure suction. Tightening torque: 7.5 N·m (0.8 kgf-m, 5.5 ft-lb) 3. Install the active grille shutter. (H4 model) Active Grille Shutter > INSTALLATION 4. Install the bumper face - front. Front Bumper > REMOVAL 5. Install the reservoir tank. Tightening torque: 7.5 N·m (0.8 kgf-m, 5.5 ft-lb) 6. Install the clutch pipe, connector and connector bracket. (MT model) Clutch Pipe and Hose > INSTALLATION 7. Install the air intake boot. Tightening torque: 3 N·m (0.3 kgf-m, 2.2 ft-lb) 8. Install the battery and battery box. • H4 model: Battery > INSTALLATION • H6 model: Battery > INSTALLATION 9. Connect the ground terminal to battery sensor. NOTE 10. Charge refrigerant. Refrigerant Charging Procedure > PROCEDURE |
Inspection
1. Check the hoses for cracks, damage and expansion. Replace the hose if faulty.2. Check the pipes for crack or damage. Replace the pipe if faulty. ...
Other materials:
Dtc p081a starter disable circuit low
DTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:Failure of engine to startCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION, and Inspection Mode Inspection Mode > PROCEDURE.WIRING DIAGRAM:Engine Electrical System ENGI ...
